Oki B930d Instrukcja Użytkownika

B930

B930 User’s Guide> 4Replacing the Transfer Roll Cartridge . . . . . . . 114Maintenance Kit . . . . . . . . . . . . . . . . . . . . . . . . 115Tr

B930n User’s Guide> 94PRINTING To specify the output format of printing, enter the following command: -C, [Parameter], [Parameter] Enter a ",&

B930n User’s Guide> 95> The EWS allows more detailed settings. 2. Setting up the Macintosh Install the printer driver (Adobe PS) for Macintosh.

B930n User’s Guide> 96• The setup procedures and commands may vary according to different versions of OS. Refer to the manuals that came with the w

B930n User’s Guide> 97Print • In the spool mode, up to 32 files can be printed by one command. Files that come after the 32nd file will be ignored.

B930n User’s Guide> 98• Print data which is in the process of printing may not be deleted. Inquiry • Long file names will be truncated. • Up to 64

B930n User’s Guide> 99INSTALLING CONSUMABLESThe Drum Unit and Toner Cartridge should be replaced when they have reached the end of their print life

B930n User’s Guide> 1001. Open the printer front and side covers.2. Remove the Drum Cartridge from the packing.3. Remove the protective sheet from

B930n User’s Guide> 1014. Avoid contact with internal surfaces and limit exposure to light for no longer than 5 minutes.5. Fold the handle down and

B930n User’s Guide> 1026. Seat the Drum Cartridge firmly into the printer.7. Remove and discard the protective strip.8. Close the printer covers.

B930n User’s Guide> 103INSTALLING THE TONER CARTRIDGEWhen installing the Toner Cartridge, take note of the following points:WARNING> Never throw

B930n User’s Guide> 5ABOUT THIS MANUALThank you for selecting the B930n 50 ppm Laser printer. This manual contains all of the information necessary

B930n User’s Guide> 1042. Remove the Toner Cartridge from its packing.3. Take the Toner Cartridge out of the box and shake it 8 to 10 times as show

B930n User’s Guide> 1054. Slide the Toner Cartridge into the printer and seat firmly in place. 5. Close the printer covers.

B930n User’s Guide> 116TROUBLESHOOTINGYour printer’s Operator Panel provides you with information and troubleshooting help. When an error or warnin

B930n User’s Guide> 117POOR PRINT QUALITYWhen the print quality is poor, select the closest symptom from the following table to rectify the problem

B930n User’s Guide> 118Black Prints - The entire printed page is black.1. The drum cartridge may be defective.2. Printable data from the computer m

B930n User’s Guide> 119Horizontal Dark Streaks - There are black lines that appear horizontally on the page.1. The drum cartridge may be defective

B930n User’s Guide> 120Unfused or Partially Fused Image - The printed image is not fully fused to the paper and easily rubs off.1. The paper may be

B930n User’s Guide> 121Blurred Prints - The image is blurred at theedges.1. The paper may be in poor condition.2. The paper may be damp.3. The drum

B930n User’s Guide> 122NO POWERCANNOT PRINTSTATUS ITEMS TO CHECK ACTIONThere is no power. Is the power switched off? Press the printer switch to th

B930n User’s Guide> 123PRINTING IS NOT CLEARPAPER INCORRECTLY FEDSTATUS ITEMS TO CHECK ACTIONTransparencies are not printed clearly.Are the correct

B930n User’s Guide> 6The basic printer consists of the print engine main unit, consumables, 100 Sheet Multi Purpose Feeder (MPF) as well as Trays 1

B930n User’s Guide> 124NOISENETWORK TROUBLESHOOTINGUSING TCP/IP This section provides information on the possible causes, verifying methods and rec

B930n User’s Guide> 125WHEN USING WINDOWS 95/98/MECAUSE TREATMENTThe printer and the computer are connected to different networks.Status Display Un

B930n User’s Guide> 126USING WINDOWS NT 4.0/2000/XP/VISTA/SERVER 2003The Printer Is Not Printing Unable to obtain the desired print resultsCAUSEVER

B930n User’s Guide> 127WHEN USING UNIXThe printer is not PrintingCAUSEVERIFICATIONACTIONIncorrect IP address. Ask the network administrator to chec

B930n User’s Guide> 128Unable to obtain the desired Print ResultsThe data format of the print job does not conform to the printing environment of t

B930n User’s Guide> 129USING ETHERTALK This section provides information on the possible causes, verifying methods and recommended actions pertaini

B930n User’s Guide> 130The printer is not connected.Cause 1 On the Macintosh, the printer is not selected correctly in the Chooser. Or, the printer

B930n User’s Guide> 131Although it is connected,the printerdoes not print.Cause 1 The printer is in the offline status.Verification 1 Check whether

B930n User’s Guide> 132ERROR AND WARNING MESSAGESMESSAGE DESCRIPTION0-1 Main MotorCall ServiceSystem Error1-1 Main MotorCall ServiceMain Motor Erro

B930n User’s Guide> 1334-6 Paper JamClear Area A/EExit Area Jam8-2 Paper JamClear Area A/EDM Area Jam6-1 through 6-2 Feed ErrorClear DuplexerDM Are

B930n User’s Guide> 7SAFETY NOTESFor your own safety, please read this page carefully before using the machine.• Do not place the machine in a hot,

B930n User’s Guide> 1344-4 Feed ErrorClear Area BPaper Tray Area - Misfeed Jam5-1 Feed Error Clear Area B/CPaper Tray Area - Misfeed Jam5-2 Feed Er

B930n User’s Guide> 1354-61 Finish JamClear Area HFinisher Jam (Compiler No Paper sensor)4-66 Finish JamClear Area HFinisher Jam (Compiler No Paper

B930n User’s Guide> 136Paper Out Tray 1Paper Out Tray 2Paper Out Tray 3Paper Out Tray 4Paper Out Tray 5Paper Out HCF8-3 EP CartridgeReset EP CartDR

B930n User’s Guide> 1375-12 FIN ErrorCall ServiceMechanical failure in Stacker Tray5-13 FIN ErrorCall ServiceMechanical failure in Stacker Tray5-21

B930n User’s Guide> 1382-8 Duplex ErrorCall ServiceDM MODEL ERRORStaple FailCheck StaplerStaple NGStaple Set ErrorCheck StaplerStaple Set Over Coun

B930n User’s Guide> 1391-2 EP CartridgeReplace EP CartToner Cartidge EmptyToner Low Toner Cartidge LowATC sensor Warning ATC sensor WarningTemp sen

B930n User’s Guide> 106MAINTENANCECLEANING THE PRINTERThis section describes how to clean the printer in order to maintain the printer in good cond

B930n User’s Guide> 107> CAUTION: Never touch areas labelled as “High Voltage.” You can get an electric shock. Never touch a labelled area found

B930n User’s Guide> 108recessed areas provided on both sides of the printer. Never try to lift the printer by gripping any other areas. Lifting the

B930n User’s Guide> 1093. Remove any paper in the MPF Tray (1). 4. Pull out the remaining paper trays and remove any paper. Keep the paper wrapped

B930n User’s Guide> 8GETTING TO KNOW YOUR PRINTERFRONT VIEW No. Name1 Front Door2 Two 500-sheet feeders (Trays 1 and 2)3 Optional Duplex Unit4 Mult

B930n User’s Guide> 1105. Open the front and side covers. NOTE> Do not touch any parts inside the printer. 6. Hold the Drum Cartridge by the gri

B930n User’s Guide> 1117. Hold the Toner Cartridge securely and pull it out slowly.NOTE> Do not shake the Toner Cartridge after it has been remo

B930n User’s Guide> 1129. Lift the printer and move it gently. If the printer is to be moved over a long distance, pack it inside a box. FUSER UNIT

B930n User’s Guide> 1132. Open the printer left side door.3. Loosen the two knobs securing the Fuser to the frame.4. Pull the Fuser toward you by h

B930n User’s Guide> 114TRANSFER ROLL CARTRIDGEThis section explains about the transfer roll cartridge. CAUTION ON HANDLING THE TRANSFER ROLL CARTRI

B930n User’s Guide> 1153. Pinch the hooks at each end of the Transfer Roller and lift to remove the Transfer Roller from the chute.4. Grasp the new

B930n User’s Guide> 140CLEARING PAPER JAMSWhen there is a paper jam, refer to the following procedures and follow the instructions.CAUTION> CAUT

B930n User’s Guide> 1411. Open Door A.2. Pull the jammed paper out of the printer. If necessary, press the green handle to move the paper to make i

B930n User’s Guide> 1423. Close Door A.JAM AT BFollow these steps to clear the jam.1. If the printer has the 2000-Sheet Feeder (Tray 6), slide the

B930n User’s Guide> 1432. Open Door B.3. Pull the jammed paper out of the printer. Confirm that all paper fragments are removed.

B930n User’s Guide> 9REAR VIEW9 Stacker Main Bin (3000 Sheets)10 Stacker Upper Bin (500 Sheets)11 Exit 2 is used in conjunction with duplex unit an

B930n User’s Guide> 1444. Close Door B.5. If the printer has the 2000-Sheet Feeder (Tray 6), slide the feeder firmly against the printer.JAM AT CFo

B930n User’s Guide> 1451. If the printer has the 2000-Sheet Feeder (Tray 6), slide the feeder away from the printer.2. Open Door C.

B930n User’s Guide> 1463. Pull the jammed paper out of the printer. Confirm that all paper fragments are removed.4. Close Door C.

B930n User’s Guide> 1475. If the printer has the 2000-Sheet Feeder (Tray 6), slide the feeder firmly against the printer.JAM AT DFollow these steps

B930n User’s Guide> 1482. Pull the jammed paper out of the printer. Confirm that all paper fragments are removed.3. Close Door D.JAM AT EFollow the

B930n User’s Guide> 1491. Open Door A.2. Open Door E.

B930n User’s Guide> 1503. Pull the jammed paper out of the printer. Confirm that all paper fragments are removed.4. Close Door E.

B930n User’s Guide> 1515. Close Door A.JAM AT FFollow these steps to clear the jam.1. Open Door F.

B930n User’s Guide> 1522. Pull the jammed paper out of the printer. Confirm that all paper fragments are removed.3. Close Door F.JAM AT GFollow the

B930n User’s Guide> 1531. If visible, pull the jammed paper out of the stacker upper tray.2. Open Door G.3. Depending on the instructions shown on

B930n User’s Guide> 10Data I/O connector settings can be configured via the Operator Panel’s Interface Menu. There are settings for Ports, Parallel

B930n User’s Guide> 1545. Pull the jammed paper out of the printer. Confirm that all paper fragments are removed.6. Close the handles opened in Ste

B930n User’s Guide> 1552. Pull the jammed paper out of the printer. Confirm that all paper fragments are removed.3. Close Door H.JAM AT THE STACKER

B930n User’s Guide> 1562. Open Door G.3. Close Door G.

B930n User’s Guide> 157PAPER JAM IN TRAY 5 (MPF)Follow these steps to clear the paper jam in Tray 5.1. Verify that the width guides are pressed aga

B930n User’s Guide> 1585. Pull the jammed paper out of the printer. If necessary, press the green handle to move the paper to make it easier to rem

B930n User’s Guide> 1591. Pull out the tray specified on the Operator Panel.2. Verify that the length and width guides are pressed against the pape

B930n User’s Guide> 1605. Open Door A.6. Pull the jammed paper out of the printer. If necessary, press the green handle to move the paper to make i

B930n User’s Guide> 1617. Close Door A.PAPER JAM IN TRAY 6Follow these steps to clear the paper jam in Tray 6.1. Pull out Tray 6.2. Verify that the

B930n User’s Guide> 162NOTE> The default setting is for 8.5 x 11 in. paper. You must change the guides for A4 paper.3. Push the tray completely

B930n User’s Guide> 1636. Pull the jammed paper out of the printer. If necessary, press the green handle to move the paper to make it easier to rem

B930n User’s Guide> 11TURNING THE PRINTER ON AND OFFSwitch on the power before operating the printer. When you have finished using the printer for

B930n User’s Guide> 164INSTALLING ACCESSORIESDUPLEX MODULECAUTION> Be sure to switch off the power and unplug the power cord from the outlet bef

B930n User’s Guide> 1651. Unpack the Option Duplex, remove cushioning materials, and confirm that all attachments are available.2. Open Printer doo

B930n User’s Guide> 1663. Remove cover and save for possible reuse.4. Slide the Exit 2 Module into position.

B930n User’s Guide> 1675. Close printer door A.6. Place the Duplex Unit in position while inserting the 2 hooks on the bottom of the unit into the

B930n User’s Guide> 1687. Lift the Duplex Unit until the upper hooks are latched in the printer.8. Open the Duplex Unit cover by lifting latch D.

B930n User’s Guide> 1699. Twist the 2 locking screws clockwise to secure the Duplex Unit to the printer.10. Close the Duplex Unit cover.

B930n User’s Guide> 17011. Remove the printer access cover (1), connect the Duplex Unit interface cable (2) and replace the printer access cover (3

B930n User’s Guide> 1711. Switch OFF the printer power.2. Remove the power cord from the printer.3. Unpack the Paper Feeder and remove cushioning m

B930n User’s Guide> 1726. Remove the packing tape from the Paper Feeder.7. Slide out the 2 drawers.

B930n User’s Guide> 1738. Remove all packing materials from both drawers.9. Slide both drawers back into the Paper Feeder.10. Remove printer drawer

B930n User’s Guide> 12AVAILABLE PRINTER DRIVERS Drivers are available for the following Microsoft operating systems: Vista 32/64, XP 32/64, Server

B930n User’s Guide> 17411. Insert the 2 locking screws, turning clockwise to secure the printer to the Feeder.12. Replace drawer 3 back in the prin

B930n User’s Guide> 17513. Remove the printer Interface Panel Cover (1), connect the 1000 Sheet Feeder Interface Connector (2) and replace the prin

B930n User’s Guide> 1763. Unpack the Paper Feeder and remove cushioning materials.4. Slide the drawer out of the Paper Feeder.

B930n User’s Guide> 1775. Remove the packing material from the feeder drawer.6. Slide the drawer back into the feeder.7. Install the mounting brack

B930n User’s Guide> 1788. Slide the 2000 Sheet Feeder to the mounting plate guiding it on the locating pin until it latches.9. Remove the shipping

B930n User’s Guide> 17911. Connect the feeder power cord into the printer accessory outlet.12. Slide the drawer out of the feeder.13. Remove the sh

B930n User’s Guide> 18014. Adjust the feeder paper size guides.15. Load the paper tray.16. Connect the power cord.17. Turn on the power switch of t

B930n User’s Guide> 181and a 4 hole capability while in the Americas, the punch is a 3 hole punch1. Switch OFF the printer power.2. Remove the powe

B930n User’s Guide> 1824. Insert the 2 mounting screws to secure the Horizontal Transport. 5. The guides from the printer itself must be moved to

B930n User’s Guide> 1837. Insert the 2 mounting screws to secure the bracket.8. Remove all the packing materials from the Finisher.

B930n User’s Guide> 13change global printer settings. All features of the printer are accessible through the Operator Panel. These changes affect a

B930n User’s Guide> 1849. Slide the Finisher into position engaging the latching hardware10. Insert the Stacker Lower catch tray.

B930n User’s Guide> 18511. Remove the access cover and plug in the Finisher interface cable.12. Remove the printer interface cover.13. Connect the

B930n User’s Guide> 18614. Connect Finisher power cord to the printer accessory power connection.15. Level the Finisher making it parallel to the p

B930n User’s Guide> 18716. Open the Finisher door.17. Remove the internal tags and shipping brackets.

B930n User’s Guide> 18818. Move the catch to the right.19. Insert the staple module

B930n User’s Guide> 18920. Unpack the paper punch waste container.21. Insert the punch waste Dust container

B930n User’s Guide> 19022. Fully seat into position.23. Close the Finisher door.HARD DISK OPTION1. Carefully review the safety precautions in the f

B930n User’s Guide> 1914. Remove side cover from printer.5. Turn thumbscrews on controller assembly counter clockwise until loose and gently pull c

B930n User’s Guide> 1927. Seat the Hard Drive over the locating pins and push firmly to seat the unit.8. Reinstall the side covers in reverse order

B930n User’s Guide> 1934. Turn screws on controller assembly counter clockwise until loose and gently pull cover towards you to remove from printer

B930n User’s Guide> iiCopyright Information ______________________________________Copyright © 2008 by Oki Data Americas, Inc. All Rights Reserved.D

B930n User’s Guide> 14LED INDICATORSThe LED indicators also indicate printer status. The three indicators can each be on, off, or blinking, indicat

B930n User’s Guide> 194OPERATOR PANELThis Appendix provides a description of Operator Panel Menu and menu item. Navigate to items as described in “

B930n User’s Guide> 195Lines per Page 57-Executive 39-Monarch Envelope 51-Com10 Envelope 46-DL Envelope 48-C5 Envelope 47-Com9 Envelope 29-A6 43-A5

B930n User’s Guide> 196System Adjust MenuPCL Tray 1 ID# 1 PCL tray IDPCL Tray 2 ID# 4 PCL tray IDPCL Tray 3 ID# 5 PCL tray IDPCL Tray 4 ID# 6 PCL t

B930n User’s Guide> 197Tray 2 Media Type Plain Set the media typeTray 3 Media Type Letter Set the media sizeTray 4 Media Type Plain Set the media t

B930n User’s Guide> 198Tray 5 Y Dimension 2216mm Set the paper lengthPrinter Sys Config MenuPersonality Auto Emulation PCL Postscript 3Auto Emulati

B930n User’s Guide> 199Character Set Set-2 Default character setSymbol Set 8U:Roman 8 Default fontLetter O Style Disable Selects replacing ¢(9b) an

B930n User’s Guide> 200DTR Onl/Offl Off Serial SignalDTR Error Off Serial SignalRTS Ready/Busy Serial Signal On/OffRTS Onl/Offl Off Serial Signa

B930n User’s Guide> 201Delete Delete selected spool fileDelete selected spool fileDestination Spool device Spool deviceSave/Restore Save MenuRestor

B930n User’s Guide> 202Current SettingsFrame TypeNetware ModePServer Mode SettingsPrint Server NameNDS Tree NameNDS ContextJob Poll IntervalNPRINTE

B930n User’s Guide> 203SNMP Trap SettingsTrap C o m m u nity Printer Trap AddressPrinter Trap AssignmentsUser Flash DirectoriesDelete Selected File

B930n User’s Guide> 15To navigate the menus, use a combination of the Menu, Select, Next and Previous buttons to scroll your way through the Menu M

B930n User’s Guide> 204Copies Execute Print media info and directoryPrint Summary Execute Print media info and directoryCFLASH Summary Execute Prin

B930n User’s Guide> 205Restore Port to Factory Defaults Execute Reset menu to defaultRestore Net to Factory DefaultsExecute Reset menu to defaultUs

B930n User’s Guide> 16In your web browser, type the IP address assigned to the printer. For example http://192.0.0.1NOTE> If there is a conflict

B930n User’s Guide> 17all jobs access Printing properties via your Printers and Faxes Menu. To make changes that apply to documents printed from a

B930n User’s Guide> 18The Printer Properties window appears.To access Printer Properties from Printers and Faxes (Windows):1. Select the Printers a

B930n User’s Guide> 19The Printer’s configuration window appears.3. On the General Tab, click Printing Preferences

B930n User’s Guide> 20The Printer Properties window appears.PAPER USAGEThis printer can print on paper that is commonly sold. Select paper suitable

B930n User’s Guide> 21STANDARD PAPERThe standard paper that can be used for this printer is as follows. Manufacturer Paper size WeightXerox Busines

B930n User’s Guide> 22SPECIAL MEDIA TYPESThe printer can also print on the following media types. These types of media are called special media. Th

B930n User’s Guide> 23Heavy media Letter 32 Lb. / 120 GSMXerox Digital Color Xpressions+ Heavy media Letter 32 LB/120G Hammermill Laser PrintHeavy

B930n User’s Guide> iiiData Loss in Hard Disk/Compact Flash DiskSaved data may be lost if the hard disk/compact flash in the machine breaks down du

B930n User’s Guide> 24PAPER TRAY CAPACITYPaper that can be loaded in the paper trays is as follows:AVAILABLE PAPER SIZESAll trays but MPF have pape

B930n User’s Guide> 25B5 (182x257mm)O-OO-OB4 (257x364)O-OO-OLegal 13(8.5”×13”)O-OO-O Legal 14(8.5”×14”)O-OO-OA3(297x420mm)O-OO-O Tabloid(11” ×17”)O

B930n User’s Guide> 26UNUSABLE PAPERUsing the following types of paper might cause paper jams, malfunctions or damage to the printer. Do not use th

B930n User’s Guide> 27• Curled paper• Paper with static electricity • Adhesive paper• Postcards with pictures• Paper with special coating on its su

B930n User’s Guide> 28POWER SAVER MODESThis printer is equipped with a low power mode to reduce power consumption when it is left idle.When no prin

B930n User’s Guide> 29BASIC PRINTING TASKSPRINTING A CONFIGURATION SUMMARYYour printer can print a configuration summary that lists the currently s

B930n User’s Guide> 302. Fan the paper to release sheets that may stick together.3. Add paper to the tray without exceeding the maximum level.NOTE&

B930n User’s Guide> 314. Insert the paper into the tray. If necessary, adjust the paper guides to the size of the paper.5. Slide the paper tray bac

B930n User’s Guide> 32LOADING MPF (TRAY 5)The MPF can be used for both manual and automatic feeds. There is an indicator label on the tray that sho

B930n User’s Guide> 333. Fan the paper to release sheets that may stick together.4. Insert the paper into the tray. If necessary, adjust the paper

B930n User’s Guide> ivPREFACEThank you for choosing this printer. This is a guide on operating this printer and the important points to note. To un

B930n User’s Guide> 342. If loading paper with a different width or length, adjust the width and length guides.3. Fan the paper to release sheets t

B930n User’s Guide> 354. Insert the paper into the tray.5. Push the tray completely into the printer.PRINTING A TEST PAGEYou can print a Demo (test

B930n User’s Guide> 36BASIC PRINTINGWhen you send a job to the printer, you should select the paper size, number of copies, orientation, and decide

B930n User’s Guide> 37The most convenient way to enable this feature is by using your Printer Properties. You may also enable this feature at the O

B930n User’s Guide> 38PRINTING IN REVERSE ORDERBy default the printer prints jobs from back to front placing the first page of the document on the

B930n User’s Guide> 39BINDING PREFERENCESYou can select how the printer will orient the page layout when duplexing. Depending on your page orientat

B930n User’s Guide> 40• Remove all other media before loading transparencies into the tray.• Do not load transparencies above the fill line; this m

B930n User’s Guide> 415. Select Transparency as the Media Type from the Media type pulldown.6. Click OK.ENVELOPESEnvelopes can be printed using Tra

B930n User’s Guide> 42• Place the envelope with the Flap entering the printer first.2. Adjust the paper guides to the size of the envelopes.3. Chan

B930n User’s Guide> 43• Insert Small postcards short-edge feed and facedown. Place the top of the postcard toward the rear of the printer.2. Adjust

B930n User’s Guide> vCONVENTIONS1. In this guide, “computer” refers to both the personal computer and workstation. 2. The following headers are use

B930n User’s Guide> 44• Trays 1-4 - Insert the label sheets long-edge feed and faceup. Place the top of the page toward the front of the printer.•

B930n User’s Guide> 45CUSTOM SIZE PAPERYou can print custom size from Trays 1 through 5. Tray 6 only prints standard paper. The following paper siz

B930n User’s Guide> 467. Click OK.8. Click OK.9. Click OK.TRAY SETTINGSYou can configure a variety of settings for your input trays and output bins

B930n User’s Guide> 47INPUT TRAY LINKING When an input tray runs out of paper, auto tray changing enables the printer to switch to another availabl

B930n User’s Guide> 482. Select Manual Feed.3. Click OK.MEDIA CHECKBy default the printer selects the input source based on the paper size requeste

B930n User’s Guide> 49The most convenient way to enable this feature is by using your Printer Properties. You may also enable this feature at the O

B930n User’s Guide> 50USING THE HOLE PUNCHERThe optional Finisher contains the Hole Puncher. When installed, a 3-hole or 2/4-hole puncher is availa

B930n User’s Guide> 513. Place the Punch Waste Box back into the Finisher.4. Close Door G.USING THE STAPLERSeveral stapling options are available.

B930n User’s Guide> 52Bottom-left PortraitLandscapeDual PortraitLandscapeSTAPLING SELECTIONORIENTATION STAPLE PLACEMENTAAAA

B930n User’s Guide> 53The most convenient way to enable this feature is by using your Printer Properties. You may also enable this feature at the O

B930n User’s Guide> viILLEGAL COPIES AND PRINTOUTSCopying or printing certain documents may be illegal in your country. Penalties of fines or impri

B930n User’s Guide> 543. Remove the staple unit by lifting it up and out.4. If present, remove the depleted staple cartridge.5. Insert a new staple

B930n User’s Guide> 55CANCELLING/CHECKING PRINTINGCANCELLING PRINTINGTo cancel printing, you can either cancel the print job at the printer or at t

B930n User’s Guide> 56ADVANCED PRINTING TASKSCOVER PAGESA cover page is the first page of the document. The printer enables you to choose a differe

B930n User’s Guide> 571. Select Standard Nup from the Finishing Mode pulldown in the Setup Tab of your Printer Properties.2. Click Options.The Stan

B930n User’s Guide> 58Select the desired number of signature from the pulldown. Signature sets the number of pages printed on a sheet to form a boo

B930n User’s Guide> 591. Select the Paper Feed button in the Setup tab within your Printer Properties.The Paper Feed Options window appears.2. Clic

B930n User’s Guide> 605. Enter the text to be displayed.6. Enter the font, typeface, and size of the text.7. Enter the angle of rotation of the tex

B930n User’s Guide> 61Using the EWS, you must have enabled email send and set the email server address for this feature to work.To email notificati

B930n User’s Guide> 621. Select the Job Options tab within your Printer Properties.2. Click Secure Print3. Enter the name of the job 4. Enter PIN n

B930n User’s Guide> 634. Enter the name of the job 5. Enter PIN number to be entered at the Operator Panel.6. Click OK.To print the proof:1. At the

B930 User’s Guide> 1TABLE OF CONTENTSAbout This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 5Conventions. . . . . . . . . . . . . . .

B930n User’s Guide> 642. Click Timed Job.3. Click Set Time.4. Enter the elapsed time or real desired.For elapsed time, specify the number of minute

B930n User’s Guide> 65DIRECT PDF PRINTINGThe printer’s PDF Direct feature allows you to send a Version 1.3 PDF file directly to the printer without

B930n User’s Guide> 665. Click OK to close the Overlay window6. Click OK to close the printer properties. When you do, a window will popup asking y

B930n User’s Guide> 67as a .csv file by an administrator via the printer EWS and processed off line by the users accounting application.

B930n User’s Guide> 68SENDING FILESAccessed via the Send File menu in the EWS, this page allows you to select a file from the client computer (or a

B930n User’s Guide> 69NETWORKINGSUPPORTED ENVIRONMENT This printer can be connected to a network through the Ethernet interface. The printer suppor

B930n User’s Guide> 70Important • The EtherTalk port setting in this printer is disabled by default. To use this port, enable the setting on the Op

B930n User’s Guide> 711. Launch the EWS using the IP address for the printer you are configuring.2. Enter the username and password for the Adminis

B930n User’s Guide> 72The network printer supports TCP/IP protocol that can be used in conjunction with the Windows operating system. Once the prin

B930n User’s Guide> 73been installed refer to the section below Installation of TCP/IP protocol. 2. If not already configured, a suitable IP addres

B930 User’s Guide> 22-Sided Printing . . . . . . . . . . . . . . . . . . . . . . . . . 38Binding Preferences . . . . . . . . . . . . . . . . . .

B930n User’s Guide> 746. The Windows NT installation CD-ROM may be required. Follow the remaining dialogue box prompts. WINDOWS 2000 1. Click the [

B930n User’s Guide> 75Once the protocol has been installed and configured in Windows, the next step is to configure the TCP/IP parameters in the ne

B930n User’s Guide> 766. In [Name or address of server providing lpd] type the host name or IP address of the host for the printer you are adding.

B930n User’s Guide> 771. Select [Start], [Settings], [Control Panel and Printers]. 2. Open the [Printers] folder. 3. Double-click [Add Printer] and

B930n User’s Guide> 7813. Select [OK]. 14. Select [Follow the instructions on the screen to finish installing the printer.]WINDOWS XP AND VISTAWind

B930n User’s Guide> 79the above IP address is entered, the Port Name will default to IP_172.168.1.31. 9. Click [Next]. [Additional Port Information

B930n User’s Guide> 8013. Click [OK]. 14. Follow the instructions on the screen to finish installing the printer.CREATING A SHARED PRINTER Create a

B930n User’s Guide> 81OKI LPR The OKI LPR Utility is network software which supported TCP/IP printing on Windows Me, Windows 98, and Windows 95. It

B930n User’s Guide> 8214. Select [Add Printer] on the [Remote Print] menu. 15. Select [Printer] to accept the printer that has been added in Step 1

B930n User’s Guide> 83The printer LPD supports Spool Mode where print jobs from clients are spooled once before output and Non-spool Mode where pri

B930 User’s Guide> 3Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69SUPPORTED ENVIRONMENT . . . . . . . . . . . . . . . .

B930n User’s Guide> 84> > The EWS allows more detailed settings. 2. Settings of the workstation Set the printer in the workstation. Refer to:

B930n User’s Guide> 853. Registering a logical PostScript printer PS01 set using the EWS. #lpadmin -p P003 -s printer1\!PS01NOTE> Enter the host

B930n User’s Guide> 86-n No. of copies This option specifies the number of copies. If one "lp" command is issued to print multiple files,

B930n User’s Guide> 87Printer name This option specifies the printer name. The "cancel" command can be effectively used with the combined

B930n User’s Guide> 88Sample To cancel the print data related to the files of printer "P001" (Job number: P001-27), enter the following c

B930n User’s Guide> 89-u [User name] This option displays received print data information on users of specified user names. -v [Printer name] This

B930n User’s Guide> 90NOTE> Any parameter other than below becomes invalid if specified. Selecting a Paper Tray When selecting a paper tray, eit

B930n User’s Guide> 91> If an unacceptable combination is specified, the printer may not operate correctly.> For some print language, the spe

B930n User’s Guide> 92NOTE> If several parameters are specified in one "lpr" command, data may not be printed correctly. > The syst

B930n User’s Guide> 93> The system default is used if no parameter is specified. > If the print data specifies 2 sided or 1 sided printing, t